TMA2063F00V1-1

TMA2063F00V1-1

TWIN TMA EU800

Designed for use in the European 800MHz frequency band the TMA2063 provides a tower mounted amplifier with excellent noise figure performance for improving both coverage and capacity on the LTE network

FEATURES

  • Improved base station sensitivity through gain in the 800 uplink band
  • Hardware and software configuration using AISG “personality” upload
  • Excellent noise performance and high linearity
  • High reliability with full lightning protection and a fail-safe bypass mode

technical specifications
downlink (tx) path
Passband791 - 821MHz
Return loss18dB minimum
Insertion loss0.3dB typical
Maximum input power with no damage250W (average) / 3kW (PEP)
uplink (rx) path
Passband832 - 862MHz
Nominal gain12dB
Gain variation over frequency, temperature±1dB maximum
Noise figure1.2dB typical
Return loss18dB minimum operating, 15dB minimum in bypass mode
Bypass loss2.9dB typical
Output IP3+22dBm typical
Maximum input power with no damage+12dBm maximum
rms evm based on a 20mhz lte signal (100 resource blocks)
RMS EVM U/L1% maximum
RMS EVM D/L1% maximum
electrical
Impedance50ohms
Intermodulation products-153dBc maximum at antenna ports with 2 x 20W carriers
power supply and alarm (current window alarm mode, default)
Current window alarm mode (CWA) is the default TMA operating mode and can be configured to specific customer requirements. The generic personality (F00V1) is configured so that both channels are independently powered and monitored via the respective BTS port. The BTS port sinks additional current to indicate an alarm state in its uplink path. Normal operating and alarm current values are configured independently and are alterable via a field-loadable personality file, contact Kaelus for more information.
DC supply voltage7.5V to 30V DC, case is DC ground
DC supply voltage via BTS-RF cableEach BTS port powered individually (programmable)
DC supply current, normal mode100 ± 20mA per port (F00V1 version, programmable)
0.85W @ 7.5V, 3W @ 30V typical
DC supply current, alarm mode180 ± 30mA per port (F00V1 version, programmable)
2.7W @ 15V per port typical
aisg mode of operation (auto selected on valid aisg 2.0 frames)
AISG signals can be applied to either BTS1 or BTS2 port. The TMA unit switches to AISG mode when valid frames are detected on one of the BTS ports. Both LNAs take DC power from the port with AISG frames or, if DC is present on both ports, both channels supply equal power to the TMA.
DC supply voltage+7.5V to +30V DC
AISG version2.0 (1.1 optional)
Supply current, AISG mode180mA @ 7.5V, 55mA @ 30V typical
AISG connector, current ratingIEC60130-9, 8-pin female, < 4A peak, 2A continuous, pin 6
Field firmware upgradableYes
environmental
For further details of environmental compliance, please contact Kaelus.
Temperature range-40º to +65ºC | -40º to +149ºF
Ingress protectionIP67
Altitude2,000m | 6,560ft
Lightning protectionIEC61312-1, RF: ±5kA maximum (8/20us), AISG: ±2kA maximum (8/20us)
MTBF>1,000,000 (hours)
ComplianceEMC:EN301 489, ETSI EN 300 019 class 4.1, RoHS
mechanical
Dimensions H x D x W250 x 300 x 86mm | 9.4 x 11.81 x 3.38in
Weight6kg | 13.2lbs estimated
FinishPainted, light grey (RAL7035)
ConnectorsDIN 7-16 (F) x 4 long neck
MountingPole/wall bracket supplied with two metal clamps 45-178mm diameter poles
ordering information
Part NumberDescription
xx denotes different personality
TMA2063F00V1-1Twin TMA, LTE800 FDD, generic personality, with AISG 2.0
TMA2063FxxV1-1Twin TMA, LTE800 FDD, with customer defined AISG personality
electrical block diagram
ELECTRICAL BLOCK DIAGRAM
mechanical block diagram
MECHANICAL BLOCK DIAGRAM

GET A QUOTE