1. Home
  2. RF Conditioning Solutions
  3. Tower Mounted Amplifiers
  4. FDD Dual Band TMAs
  5. TMA2138F03V4-2A

TMA2138F03V4-2A

TMA2138F03V4-2A

TWIN TMA 700H/850MHz

SEPARATE 700/850 ANTENNA PORTS

Designed to be deployed in co-located 700 and 850MHz networks the Kaelus TMA2138 provides gain in the 700H uplink and in the 850MHz uplink, using independent LNAs per band and per channel.

FEATURES

  • Improved base station sensitivity through excellent noise figure performance and linearity
  • AISG 2.0 compliant, software upgrade w/AISG “personality” upload
  • Suitable for CDMA and LTE signals
  • Rejection of the North American public safety band rejection allows co-location
  • AISG OOK + DC output to the antenna port of channel 1
  • AISG OUT connector disabled when AISG device (SBT equipped antenna) present on Port 1 +R1
  • One AISG subunit per LNA, 8 in total. All fixed gain.
  • Passive 698-746MHz response for feedline/antenna sweep/PIM testing
Download PDF
GET A QUOTE
Download PDF
GET A QUOTE
technical specifications
Band 700H 850
downlink
Passband 746.5 - 755.5MHz 869 - 894MHz
Bandwidth 10MHz LTE signal centred on 751MHz NA
Insertion loss 0.3dB typical 0.4dB typical
Return loss 24dB typical
Group delay variation In 5MHz = 10ns typical In 5MHz = 10ns typical
Maximum input power 60W (average) / 600W (PEP) 150W (average) / 1.5kW (PEP)
Intermodulation products -155dBc maximum, at antenna port with 2 x 20W carriers (in RX band)
uplink
Passband 777.5 - 786.5MHz 824 - 849MHz
Bandwidth 10MHz LTE signal centred on 782 MHz N/A
Gain 15dB
Gain variation ±1dB maximum ±1dB maximum in any 10MHz
±1.2dB maximum in 25MHz
Return loss 22dB typical
Bypass return loss 12dB typical
Bypass loss 3.0dB typical
Noise figure 1.6dB typical 1.3dB typical
Output IP3 +30dBm typical
Maximum input power with no damage +12dBm maximum
Group delay variation 300ns maximum In 5MHz = 300ns maximum
Rejection Rx in filter rejection 763 - 775MHz = 40dB minimum Rx in filter rejection 851 - 856MHz = 30dB minimum
700l - non intrusive pim testing
Passband 698- 746MHz
Insertion loss 0.5dB maximum
electrical
Impedance 50Ohms
power supply and alarm (current window alarm mode, default)
Current window alarm mode (CWA) is the default operating mode and can be configured to specific customer requirements. The TMA2138F03V4 is configured so that all LNAs are powered regardless of which R1/R1 AISG IN port has DC power. If DC is applied on only one port, the normal DC supply current will exceed the value tabled below. Please contact Kaelus for more information.
DC supply voltage +8.5 to +18V DC, case is DC ground
DC supply Each BTS port powered individually
DC supply current, normal mode 200mA per port typical (both ports are powered)
DC supply current, alarm mode 300mA per port typicall (both ports are powered)
aisg mode of operation (auto selected on valid aisg 2.0 frames)
AISG signals can be applied to port 5 or port 6. The TMA unit switches to AISG mode when valid frames are detected on either port 5 or 6 and the port with DC also has the AISG signalling. If DC is present on both ports, power will be supplied equally between the ports. Sub-units 1 and 2 apply to the 850 band while sub-units 3 and 4 apply to the 700 band.
DC supply voltage +7.5V to +30V DC
AISG version 2.0 (1.1 optional)
Supply current, AISG mode 500mA @ 7.5V, 135mA @ 30V typical
AISG connector, current rating IEC60130-9, 8-pin female, < 4A peak, 2A continuous, pin 6
Field firmware upgradable Yes (R951022VZA2.0 Rev 2.9.11)
AISG pass through to antenna port Yes
antenna aisg ook + dc
When DC is applied to the TMA2138F03V4 it is quickly switched through to port 3. If an over-current condition is detected, DC & AISG are disconnected from port 3. If DC remains connected to the load at port 3, DC and AISG are disconnected from the AISG OUT 8 pin connector. If DC is disconnected from port 3, DC and AISG are enabled at the AISG OUT 8 pin connector.
Mode of Operation Voltage at
Port 3		 Assumption "Autosense + Protection"
Switch Status		 Comment
AISG or CWA High Device present or
open circuit		 Close DC & AISG OOK will be
supplied to port 3.
DC & AISG is removed
from the AISG OUT 8 pin port
AISG or CWA Low DC short circuit or low
DC resistance		 Open DC & AISG OOK will not be
supplied to port 3.
DC & AISG are supplied
to the AISG OUT 8 pin port
environmental
For further details of environmental compliance, please contact Kaelus.
Temperature range -40ºC to +65ºC | -40°F to +149°F
Ingress protection IP67
Altitude 3,000m | 10,000ft
Lightning protection IEC61312-1, RF: ±5kA maximum (8/20us), AISG: ±2kA maximum (8/20us)
MTBF >1,000,000 hours
Compliance FCC Part 15 subpart B
mechanical
Dimensions H x D x W 260 x 195 x 325 mm | 10.2 x 7.7 x 12.8 in excluding brackets and connectors
Weight 19 kg | 42 lbs
Finish Painted, light grey (RAL 7035)
Connectors DIN 7-16 (F) x 12 long shank, AISG (F) x 2
Mounting Poll/wall bracket supplied with two metal clamps 45-178mm diameter poles
ordering information
Part Number Configuration Optional Features Connectors
TMA2138F03V4-1A TWIN 2 in / 4 out AISG ON ANT +R1 DIN 7-16 (F)
TMA2138F03V4-2A QUAD 4 in / 8 out AISG ON ANT +R1 DIN 7-16 (F)
electrical block diagram
ELECTRICAL BLOCK DIAGRAM
mechanical block diagram
MECHANICAL BLOCK DIAGRAM

GET A QUOTE